ClubRightHelp centre Open ClubRight

Nurturing leads with Smart Workflows

Use the Prospect Nurture workflow to automatically follow up with new prospects and encourage them to join your gym.

When someone is added as a prospect in ClubRight, the clock starts. The Prospect Nurture workflow sends a sequence of messages and creates staff follow-up tasks automatically, so no lead goes cold while your team is busy with other things. You set it up once, activate it, and ClubRight handles the follow-up from there.


Before you start

📋 Note: This article covers setting up the Prospect Nurture workflow specifically. For a general introduction to Smart Workflows, including how to navigate to them and how templates work, see Smart Workflows: getting started with automation.


How to set up the Prospect Nurture workflow

  1. Click the burger menu in the top left-hand corner.

  2. Click Communication.

  3. On the left-hand side under Navigate, click Smart Workflows. On a phone, first tap the round grey button with the sliders icon at the bottom right of the screen to open this menu.

  4. Click New workflow in the top right.

  5. In the template library, select Prospect Nurture.

You will see the full workflow structure. The trigger is set to Joins as prospect, meaning the workflow starts automatically whenever someone is added as a new prospect in ClubRight.

For what counts as joining as a prospect, see "What counts as joining as a prospect?" in Smart Workflows: getting started with automation.


Naming your workflow

On the right-hand side of the workflow editor, you can update the Name and add an optional Description to help you identify the workflow on your Smart Workflows page.


What the workflow does

The Prospect Nurture template includes seven steps:

  • Wait 2 hours: a short pause after the prospect is added before the first message goes out.

  • Send message: Thanks for your interest!: an initial welcome message sent to the prospect.

  • Wait 2 days: a pause before the next action.

  • Await approval: the workflow waits for your sign-off before continuing. Members waiting at this step are listed under Communication > Smart Workflows > Pending approvals. Click Approve to continue the workflow for that member, Skip to take them out of the workflow, or Always approve to approve them and stop this step asking for approval in future. This is a good point to skip anyone who has already joined.

  • Create task: Call new prospect to discuss options: a follow-up task is created and assigned to a staff member.

  • Wait 5 days: a further pause before the final message.

  • Send message: Ready to get started?: a follow-up message to re-engage the prospect.

Once the final step is complete, the workflow ends. Members leave the workflow at this point: it is not a step and nothing needs setting, it just marks the finish.


Does the Prospect Nurture workflow wait for approval?

Yes. Every prospect stops at the Await approval step, after the second wait, and the call task and the last message don't happen until someone approves them. Prospects waiting for approval are listed under Communication > Smart Workflows > Pending approvals.

To stop it waiting, either:

  • Click Always approve next to one of the prospects on Pending approvals. This approves them and stops the step asking for approval in future.
  • Or remove the step from the workflow:
    1. Open the workflow from Communication > Smart Workflows.
    2. If it's live, click Pause to edit.
    3. Hover over the Await approval step, click the bin icon and click Remove to confirm.
    4. Click Activate. If you're asked who the workflow should apply to, choose New members only.

New prospects then go straight on to the call task. Anyone who was already waiting at the step when you removed it stays on Pending approvals until you Approve or Skip them.


How do I stop the messages once a prospect joins?

The workflow doesn't check whether a prospect has joined, so it carries on to the end for everyone, including people who have become members since they were added. To stop it once someone joins, add a Condition step set to Is still a prospect before each message:

  1. Open the workflow from Communication > Smart Workflows.

  2. If it's live, click Pause to edit.

  3. Click Add step just before a Send message step, after the wait before it, and choose Condition.

  4. Choose Is still a prospect.

  5. Repeat this before each Send message step.

  6. Click Activate. If you're asked who the workflow should apply to, choose New members only.

Anyone who has joined leaves the workflow when they reach the condition, so they don't get that message or any of the steps after it. This also applies to prospects who are already part-way through the workflow when you add the condition.

💡 Tip: Put the condition after the wait, not before it. The check then runs just before the message goes out, so anyone who joined during the wait is caught.

For more on how condition steps work, see How do condition steps work in a Smart Workflow?.


Customising the workflow

Editing a message

To edit a message step, hover over it and click the pencil icon. This opens the Send message panel where you can:

  • Choose when the message sends: Immediately (as soon as the workflow reaches this step) or After a delay (add a wait before the message goes out).

  • Update the Subject and Message body to suit your club.

  • Personalise the message using the Insert personalisation options below the message body: First name, Membership number, Title, or additional fields via the More dropdown.

  • Choose the Channels: Smart (ClubRight automatically picks the best channel for each member), Email, SMS, or Push.

  • Set the Consent type required: Email Marketing or SMS Marketing.

Messages always go to the prospect in the workflow. You can't send a workflow message to a staff member or another email address.

Editing a task

To edit the Create task step, hover over it and click the pencil icon. This opens the Create task panel where you can:

  • Update the Task details to describe what the staff member needs to do.

  • Use the Assign to dropdown to assign the task to a specific staff member or to Member's assigned staff (which automatically routes the task to whoever is assigned to that member in ClubRight).

  • Set the number of Days to complete the task.

The task will appear in the assigned staff member's task list in ClubRight when that step is reached in the workflow. Tasks are only shown inside ClubRight, so the staff member needs a ClubRight login to see them.

Deleting a step

To remove a step from the workflow, hover over it and click the delete icon (bin) next to the pencil. This permanently removes the step from the workflow.

Adjusting the timing

To change the wait time between steps, hover over a Wait step and click the pencil icon. Update the duration to suit your follow-up schedule.

Re-enrollment

By default, a prospect will only go through this workflow once. If you want prospects to be able to re-enter the workflow after completing it, enable Allow members to re-enter this workflow in the panel on the right-hand side.


Activating the workflow

When you are happy with the workflow, click Save to keep it as a draft, or Activate in the top right to make it live.


💡 Helpful tip: The Smart channel option is a good default for most clubs. It automatically selects the best channel for each prospect based on their details, so you do not need to maintain separate email and SMS versions of the same message.